DIY Obi Wan Kenobi Star Wars Episode 1 home made lightsaber video 7 of 9

This detailed tutorial will show you how to make Obi Wan’s Lightsaber from Star Wars Episode I. There will be various tools used in the making of this saber and safety is highly advised. Each video will be pertaining to the steps indicated as a referral. Once completed, this model saber will only be good for display purposes and maybe light dueling. Please take your time and read all instructions and view all videos before assembling the saber. Patterns: http://www.mediafire.com/file/apg3esqjqoia1bn/OBI_WAN_Pattern_1.jpg/file http://www.mediafire.com/file/vf9z87mpbrid8xh/OBI_WAN_Pattern_2.jpg/file http://www.mediafire.com/file/1gqb07u26lszrr4/Duel_of_fates_2.jpg/file http://www.mediafire.com/file/9sfnrwkhn5x9om0/Duel_of_fates_1.jpg/file http://www.mediafire.com/file/7euwprrhvnxkq00/Duel_of_fates_3.jpg/file Obi Wan Kenobi Lightsaber tools and materials Tools: 1” belt X 5” disc sander or similar Cordless or power drill Dremel with flex shaft and reinforced cutoff wheels Drill bit kit Hacksaw Scissors Scotch tape ruler Fine tip marker / pencil 100 grit sandpaper and fine sandpaper (220, 320, 400) Plastic friendly glue 6-32 and 8-32 Taps (3) 8-32 X 7/16” stainless steel socket cap screws 6-32 X ½” recessed screw #6 X ½” self tapping pan head screw West System # 807 Syringes Safety: Gloves Safety glasses Hearing protection Saber parts: 12” of 1” schedule 40 white plumbing PVC pipe 12” of 1.25” schedule 40 white plumbing PVC pipe 12” X 1.25” Chrome Extension Tube Toilet Tank over flow tube 1.75” X 0.083” Wall 12” long T3 Aluminum tube (Obi Wan Emitter) 1.375” X 0.035” Wall 24” long T3 Aluminum tube (Obi Wan handle) 3/8” X 3/8” X 12” solid square metal bars (4) ½” Bell Escutcheons (chrome finish) I did say 5 but I didn’t need the other one. (1) 7/8” or ¾” copper “flat” Escutcheons (12) 1.25” rubber slip joint washers # 7202C (buy extra just in case) (2) 1.25” plastic slip joint washers # 7196C (buy extra just in case) Lavatory Pop Up Drain Gasket Toilet Bolt Caps (ivory or white) RG-59 Twist on Connectors (gold) Lock Up Caps Covertec Clip Spray paint of choice: Rustoleom Gloss Black, Silver or Gray metallic Rustoleum Clear Coat OR Killer Chrome Spray Paint Not Mentioned: Rustoleom Gloss Apple Red spray paint Unibit AKA stepper bit (optional) Pliers and Needle Nose pliers “O” Ring 1.25” ID with a 1/8” wall. Found in Home Depot plumbing by Danco “O” Ring repair kit for Moen Spouts. Package number 80502 #8 Finishing washers Before you begin! Power / Cordless tools will be used in making this lightsaber. Whenever trimming, cutting metal and / or PVC, use safety glasses, gloves and hearing protection. Use your disc / belt sander to finish off PVC and light metal parts. Remember, think before you act on making your saber. I will not be responsible for personal and or property damage. Read instructions and / or watch videos before doing anything. NOTE TO ALL: This is the first time I have built this lightsaber and constructing it has been a challenge for me. During construction, I have made minor mistakes and/or changes that can be corrected. These corrections are made in the video(s) as well as noted in the written tutorial. Also I apologize for repeating any instructions twice in the video and going into depth with cutting and trimming.